IMPROVEMENT OF THE TECHNOLOGY FOR OBTAINING ENVIRONMENTALLY SAFE COMPOSITE MATERIALS BASED ON RECYCLED POLYMERS

Authors

  • Majidov Abdinabi Amanovich Associate Professor, Asia International University, Uzbekistan Author

Keywords:

Keywords: recycled polymers, polymer waste, composite materials, environmental safety, plastic recycling, resource conservation, polymer matrix, fillers, modifying additives, processing technology, circular economy.

Abstract

ABSTRACT. The article examines the scientific and technological foundations for improving the technology of obtaining environmentally safe composite materials based on recycled polymers. The relevance of polymer waste recycling is substantiated as an important direction of resource conservation, reduction of environmental burden, and implementation of the principles of the circular economy. Special attention is paid to the preparation of recycled polymer raw materials, the selection of environmentally safe fillers, the use of modifying additives, and the optimization of technological processing modes. It is shown that the use of mineral, natural, and combined fillers makes it possible to improve the physical-mechanical, technological, and operational properties of composites. It has been established that the quality of the materials obtained depends on the degree of raw material purification, moisture content, particle size, component ratio, processing temperature, and the efficiency of interfacial interaction between the polymer matrix and the filler. The results obtained confirm the possibility of creating composite materials with increased strength, heat resistance, water resistance, and durability. The proposed technological approach can be used in the production of construction, finishing, technical, and packaging materials based on recycled polymers.

References

1.Hopewell J., Dvorak R., Kosior E. Plastics recycling: challenges and opportunities // Philosophical Transactions of the Royal Society B. – 2009. – Vol. 364, № 1526. – P. 2115–2126. DOI: 10.1098/rstb.2008.0311.

2.Ragaert K., Delva L., Van Geem K. Mechanical and chemical recycling of solid plastic waste // Waste Management. – 2017. – Vol. 69. – P. 24–58. DOI: 10.1016/j.wasman.2017.07.044.

3.Al-Salem S. M., Lettieri P., Baeyens J. Recycling and recovery routes of plastic solid waste: a review // Waste Management. – 2009. – Vol. 29, № 10. – P. 2625–2643. DOI: 10.1016/j.wasman.2009.06.004.

4.Geyer R., Jambeck J. R., Law K. L. Production, use, and fate of all plastics ever made // Science Advances. – 2017. – Vol. 3, № 7. – Article e1700782. DOI: 10.1126/sciadv.1700782.

5.Jambeck J. R., Geyer R., Wilcox C. et al. Plastic waste inputs from land into the ocean // Science. – 2015. – Vol. 347, № 6223. – P. 768–771. DOI: 10.1126/science.1260352.

6.Andrady A. L., Neal M. A. Applications and societal benefits of plastics // Philosophical Transactions of the Royal Society B. – 2009. – Vol. 364, № 1526. – P. 1977–1984. DOI: 10.1098/rstb.2008.0304.

7.La Mantia F. P. Handbook of Plastics Recycling. – Shrewsbury: Rapra Technology Limited, 2002. – 442 p.

8.Goodship V. Introduction to Plastics Recycling. – 2nd ed. – Shrewsbury: Smithers Rapra Technology, 2007. – 184 p.

9.Wypych G. Handbook of Fillers. – 4th ed. – Toronto: ChemTec Publishing, 2016. – 938 p.

10.Yang H. S., Kim H. J., Park H. J., Lee B. J., Hwang T. S. Water absorption behavior and mechanical properties of lignocellulosic filler-polyolefin bio-composites // Composite Structures. – 2006. – Vol. 72, № 4. – P. 429–437. DOI: 10.1016/j.compstruct.2005.01.013.

11.Matuana L. M., Stark N. M. The use of wood fibers as reinforcements in composites // Biofiber Reinforcements in Composite Materials / ed. by O. Faruk, M. Sain. – Cambridge: Woodhead Publishing, 2015. – P. 648–688.

12.Faruk O., Bledzki A. K., Fink H. P., Sain M. Biocomposites reinforced with natural fibers: 2000–2010 // Progress in Polymer Science. – 2012. – Vol. 37, № 11. – P. 1552–1596. DOI: 10.1016/j.progpolymsci.2012.04.003.

13.Бобович Б. Б. Переработка отходов производства и потребления. – Москва: Интермет Инжиниринг, 2000. – 496 с.

14.Коршак В. В. Технология пластических масс. – Москва: Химия, 1985. – 560 с.

15.Крыжановский В. К., Бурлов В. В., Паниматченко А. Д. Технические свойства полимерных материалов. – Санкт-Петербург: Профессия, 2003. – 240 с.

16.Гуль В. Е., Кулезнев В. Н. Структура и механические свойства полимеров. – Москва: Высшая школа, 1979. – 352 с.

17.Кулезнев В. Н., Шершнев В. А. Химия и физика полимеров. – Москва: КолосС, 2007. – 367 с.

18.Пахомов П. М. Полимерные композиционные материалы: структура, свойства, технология. – Москва: Химия, 2010. – 320 с.

19.Власов С. В., Кандырин Л. Б., Кулезнев В. Н. Основы технологии переработки пластмасс. – Москва: Химия, 2004. – 600 с.

20.Сафин Р. Р., Разумов Е. Ю., Сафина А. В. Полимерные композиционные материалы на основе древесных наполнителей // Вестник Казанского технологического университета. – 2013. – Т. 16, № 18. – С. 156–159.

Downloads

Published

2026-06-13