This is an outdated version published on 2026-10-14. Read the most recent version.

DEVELOPMENT OF AN AUTOMATION AND INTELLIGENT CONTROL SYSTEM FOR THE DRYING PROCESS OF POLYVINYL CHLORIDE

Authors

  • Mukhammadrezaevna Sharipova, Sanjar Bakhriddinovich Boybutaev Bukhara State Technical University, Uzbekistan Author

Keywords:

polyvinyl chloride; suspension PVC; fluidized-bed drying; industrial automation; soft sensor; predictive control; energy efficiency.

Abstract

This study develops a structured automation and intelligent control concept for suspension-grade polyvinyl chloride (S-PVC) drying. The proposed architecture combines industrial instrumentation, a model-assisted outlet-moisture soft sensor, online bias adaptation, and constrained model predictive control (MPC). A control-oriented drying model represents moisture removal by an effective rate coefficient and first-order outlet dynamics with transport delay. A reproducible four-hour numerical experiment compares a conventional PI controller with the bias-adaptive MPC under stepwise variations in wet-cake moisture. For the explicitly assumed nominal parameters, MPC reduced the calculated mean utility-demand proxy from 303.19 to 300.31 kW (0.95%) and reduced the proportion of simulated time above the illustrative 0.43% dry-basis moisture limit from 20.4% to 0.0%. A ±10% kinetic-parameter sensitivity test showed both the value and the limitations of online model correction. These are model-based findings, not results of industrial commissioning or laboratory validation. The paper specifies an implementation and validation route for production-scale deployment.

References

1.Aubin, A., Ansart, R., Hemati, M., Lasuye, T., & Branly, M. (2014). Modeling and simulation of drying operations in PVC powder production line: Experimental and theoretical study of drying kinetics on particle scale. Powder Technology, 255, 120–133. https://doi.org/10.1016/j.powtec.2013.08.019

2.de Araújo, A. C. B., Vasconcelos, L. G. S., Alves, J. J. N., & Shang, H. (2011). Optimal operation of an industrial PVC dryer. Drying Technology, 29(1), 19–34. https://doi.org/10.1080/07373937.2010.482713

3.Aubin, A., Ansart, R., Hemati, M., Lasuye, T., & Branly, M. (2016). Determination of PVC powder drying kinetics at particle scale: Experimental study and modeling. Drying Technology, 34(16), 2000–2023. https://doi.org/10.1080/07373937.2016.1155596

4.Tacidelli, A. R., Pereira Neto, A. T., Brito, R. P., de Araújo, A. C. B., Vasconcelos, L. G. S., & Alves, J. J. N. (2012). Modeling and simulation of industrial PVC drying in fluidized beds with internal heat source. Chemical Engineering & Technology, 35(12), 2107–2119. https://doi.org/10.1002/ceat.201100713

5.Banooni, S., Hajidavalloo, E., & Dorfeshan, M. (2018). Experimental and numerical study of the effects of pre-drying of S-PVC using a pneumatic dryer. Powder Technology, 338, 220–232. https://doi.org/10.1016/j.powtec.2018.06.027

6.Dorfeshan, M., Mehrzad, S., & Hajidavalloo, E. (2022). Experimental and numerical investigation of specific energy consumption of the two-stage pneumatic-fluidized bed drying of suspension-grade polyvinyl chloride. Drying Technology, 40(2), 371–386. https://doi.org/10.1080/07373937.2020.1812632

7.Mujumdar, A. S. (Ed.). (2014). Handbook of industrial drying (4th ed.). CRC Press.

8.Kudra, T., & Mujumdar, A. S. (2009). Advanced drying technologies (2nd ed.). CRC Press.

9.Qin, S. J., & Badgwell, T. A. (2003). A survey of industrial model predictive control technology. Control Engineering Practice, 11(7), 733–764. https://doi.org/10.1016/S0967-0661(02)00186-7

10.Morari, M., & Lee, J. H. (1999). Model predictive control: Past, present and future. Computers & Chemical Engineering, 23(4–5), 667–682. https://doi.org/10.1016/S0098-1354(98)00301-9

11.Kadlec, P., Gabrys, B., & Strandt, S. (2009). Data-driven soft sensors in the process industry. Computers & Chemical Engineering, 33(4), 795–814. https://doi.org/10.1016/j.compchemeng.2008.12.012

12.Kano, M., & Fujiwara, K. (2013). Virtual sensing technology in process industries: Trends and challenges revealed by recent industrial applications. Journal of Chemical Engineering of Japan, 46(1), 1–17. https://doi.org/10.1252/jcej.12we167

13.Seborg, D. E., Edgar, T. F., Mellichamp, D. A., & Doyle, F. J., III. (2016). Process dynamics and control (4th ed.). Wiley.

14.Isermann, R. (2006). Fault-diagnosis systems: An introduction from fault detection to fault tolerance. Springer. https://doi.org/10.1007/3-540-30368-5

15.Talele, P., Chaudhari, V. D., Talele, H., & Chaudhari, D. V. (2025). Evolution of drying process modeling: From mathematical foundations to machine learning-driven prediction and control. Journal of Food Process Engineering, 48(12), e70300. https://doi.org/10.1111/jfpe.70300

Downloads

Published

2026-10-14

Versions